Nayla_1068
2014-04-03 17:47:25
- #1
Hello everyone,
I can say something about the dishwasher mounts from Ikea, I hope it is still needed.
RESONLIG is, as already mentioned, for the fully integrated dishwashers from Ikea that were built after 08.2012. These appliances have, among other things, guides on the outside of the plastic panel to accommodate the sliding hinge. We are thus talking about Rengöra, Skinande, the new LAGAN, and some Renlig models. Enastaende, as you already said, has the sliding hinge included.
Behjälplig is for Hjälpsam and fully integrated Ikea appliances that were built before 08.2012, and third-party appliances. However, it cannot/must not be guaranteed that the mount fits securely here. The special feature of Behjälplig is that the mount is additionally attached to the neighboring cabinets. It is therefore not possible to place an appliance using this fixture at the end. The dishwasher should always be connected to a carcass on the right and left, or at least to a dropped countertop. By the way, with Behjälplig, it doesn’t matter at all whether the dishwasher is 45 or 60 cm wide.
Then there is Ersättare. Such a mount apparently already exists from other providers. This system is not particularly aesthetically pleasing with Metod, as the front is longer than the adjacent ones. We are talking about approximately a 13 cm control panel, a 10 cm drawer front, a 40 cm or two 20 cm fronts, and a 20 cm panel at the bottom, totaling 83 cm next to 80 cm high carcasses. Drawer fronts MUST ALWAYS be installed because at the very bottom, a 20 cm panel is needed. This panel folds forward or upward when opening the appliance and therefore does not touch the floor. Ersättare only fits 60 cm semi-integrated appliances; there is still nothing for 45 cm.
Vaglig is used with Enastaende, Resonlig, and Behjälplig in 60 cm width to connect drawer fronts. It is not suitable for mounting directly on the front.
If the dishwasher is designed for door sizes up to 80 cm, the front can be mounted directly as usual. There are no more plinth problems because it is recessed far back.
Not quite 9 weeks left until the start in Germany. I am very curious when theory finally meets practice. Although I already know smaller sample kitchens, I would have liked to visit Lübeck, but unfortunately it is too far for a day trip.
Greetings
Nayla
I can say something about the dishwasher mounts from Ikea, I hope it is still needed.
RESONLIG is, as already mentioned, for the fully integrated dishwashers from Ikea that were built after 08.2012. These appliances have, among other things, guides on the outside of the plastic panel to accommodate the sliding hinge. We are thus talking about Rengöra, Skinande, the new LAGAN, and some Renlig models. Enastaende, as you already said, has the sliding hinge included.
Behjälplig is for Hjälpsam and fully integrated Ikea appliances that were built before 08.2012, and third-party appliances. However, it cannot/must not be guaranteed that the mount fits securely here. The special feature of Behjälplig is that the mount is additionally attached to the neighboring cabinets. It is therefore not possible to place an appliance using this fixture at the end. The dishwasher should always be connected to a carcass on the right and left, or at least to a dropped countertop. By the way, with Behjälplig, it doesn’t matter at all whether the dishwasher is 45 or 60 cm wide.
Then there is Ersättare. Such a mount apparently already exists from other providers. This system is not particularly aesthetically pleasing with Metod, as the front is longer than the adjacent ones. We are talking about approximately a 13 cm control panel, a 10 cm drawer front, a 40 cm or two 20 cm fronts, and a 20 cm panel at the bottom, totaling 83 cm next to 80 cm high carcasses. Drawer fronts MUST ALWAYS be installed because at the very bottom, a 20 cm panel is needed. This panel folds forward or upward when opening the appliance and therefore does not touch the floor. Ersättare only fits 60 cm semi-integrated appliances; there is still nothing for 45 cm.
Vaglig is used with Enastaende, Resonlig, and Behjälplig in 60 cm width to connect drawer fronts. It is not suitable for mounting directly on the front.
If the dishwasher is designed for door sizes up to 80 cm, the front can be mounted directly as usual. There are no more plinth problems because it is recessed far back.
Not quite 9 weeks left until the start in Germany. I am very curious when theory finally meets practice. Although I already know smaller sample kitchens, I would have liked to visit Lübeck, but unfortunately it is too far for a day trip.
Greetings
Nayla