Installing Siemens dishwasher in Ikea Metod kitchen

  • Erstellt am 2015-02-12 21:19:17

Jojoman

2015-03-05 08:57:36
  • #1
We took the one-piece front. We will use the 3-piece one for the refrigerator.
 

IKEA-Experte

2015-03-05 15:16:39
  • #2


Just cut out the base a little bit. With Faktum, you always had to do that. Alternatively, you could mill the fronts so that the connecting parts are recessed, but then the surface needs to be resealed again.
 

Hesse.MTK

2015-03-08 19:13:49
  • #3
I now have the one-piece version. I decided on it because of the stability. Even with flat iron, there is an enormous amount of tension on it. At the top, the plate is pulled away from the dishwasher, and at the bottom, it falls outward due to gravity.

However, I am still very satisfied with the one-piece and the dishwasher! Great machine
 

IKEA-Experte

2015-03-08 21:31:53
  • #4
Good to know that flat irons are not so recommendable after all. Pinning (or having it pinned) would probably be the best option if you want split fronts.
 

Sektionschef

2015-04-07 08:47:13
  • #5
I have now installed the Siemens dishwasher SX778D01TE in my Metod kitchen.
I mounted an 80cm front (undivided) on the dishwasher door, so I cannot report any experience with a divided front.
However, there were still some problems:
1.) I mounted a handle on the top of the front. As mentioned elsewhere, you actually have to countersink the heads of the handle screws inside; otherwise, they will hit the upper edge of the control front when closing the dishwasher door. Since the handle screws are not countersunk, I therefore enlarged the handle hole slightly inside with a larger drill bit.
2.) The installation instructions of the dishwasher state at the end that you can adjust the weight of the front, and thus the ease of the door, with 2 screws at the bottom. However, if the 80cm front is installed, you no longer have access to these screws as they are somewhere behind the front. Since the door of my device opens well and also stays in any position, I did not pursue the problem of screw access any further.
3.) As part of the dishwasher installation instructions, you have to stick a kind of rubber mat to the bottom of the dishwasher, which hangs down and is supposed to simply slide behind the plinth when closing the dishwasher door. In my case, this mat keeps coming loose and then hangs down visibly in front of the plinth. The reason is that with the dishwasher door completely open, the mat is pulled too far out behind the plinth because it is actually too short for an 8cm plinth.
I do not yet know how to solve this problem. Either the mat would have to be glued a little lower (I do not even know if I can remove the mat again) or something would have to be attached to the plinth to make it a little higher.
Has anyone else faced this problem and how did you solve it?

best regards
Section Head
 

Leuchte_4301

2015-04-07 12:51:00
  • #6
Hello,

This rubber mat also serves to reduce noise. Since I faced the same problem as you, I omitted the rubber mat. For this, you just have to loosen the front again, lift it upwards, and peel off the adhesive film. Whether with or without the rubber mat/noise insulation, I noticed no difference. According to Siemens, installation is not mandatory either.
 

Similar topics
15.02.2017Fully integrated dishwasher19
08.02.2024Problem with Hjälpsam dishwasher12
03.04.2013Corner connection 16cm skirting board11
26.05.2015Ikea METOD / Dishwasher19
06.09.2014Siemens or Bosch dishwasher combined with Behälping rail14
26.03.2015XXL dishwasher from Neff12
18.10.2015First Ikea kitchen... Now with backsplash (p. 7)61
24.06.2015IKEA METOD kitchen with Siemens dishwasher25
31.10.2015Install Bosch SMV68M90EU dishwasher in Ikea Metod23
07.09.2015Washing machine and dishwasher in Ikea Metod tall cabinet?32
07.01.2016The new kitchen will be from Ikea14
28.07.2017IKEA Laxarby fronts in white, availability11
16.05.2016Our new first Ikea kitchen - planning and preparation69
12.05.2016First IKEA kitchen planning and some questions (external appliances)16
02.09.2016Small kitchen with big possibilities wanted23
30.01.2017Ikea Metod cabinet for built-in Bosch refrigerator HND22K20011
04.12.2017Planning kitchen appliances. How to proceed. Market is not clear250
14.02.2022Kitchen consultation granite slab and Siemens appliances?78
19.07.2023Siemens Studioline - have I received all the "Monday devices"?29

Oben