FTTH/Network/DECT/IPTV is it correct?

2021-04-11 04:37:36

In your sketch there is an RJ11 to RJ45 connection between the FritzBox and the switch. What for? That doesn't work. If you want to bring analog signals (fax, analog phone) to the sockets (end devices), the above-mentioned connection from the FB to the patch panel would have to run. Get an adapter for 1.87€ TAE to RJ45 or an RJ11 to RJ45 cable for this. Pins 4+5 are usually assigned for telephony. From the socket then again a cable, e.g. RJ45 to RJ11 with assigned pins 4+5 for fax... (often no longer included...)

2021-04-11 19:34:26

Which IPTV provider is it? We have been with Telekom for years. I could share my experiences with you.

Edit: and why the Gigaset Pro and not simply GO 100?

Which switch do you use? I will also subscribe to MagentaTV and am currently looking for a suitable 24-port switch with PoE.

2021-04-11 21:13:43

My last post, although internally linked in this forum, was deleted. Try searching for Cisco and SG250X in this forum.

2021-04-11 21:36:24

In your sketch, there is an RJ11 to RJ45 connection between FritzBox and switch. For what purpose? That doesn't work. If you want to bring analog signals (fax, analog telephone) to the outlets (end devices), the aforementioned connection from the FB to the patch panel would have to run. Get yourself a TAE to RJ45 adapter or RJ11 to RJ45 cable for €1.87. Pins 4+5 are generally assigned for telephony. From the outlet onwards, use a cable, e.g. RJ45 to RJ11 with pins 4+5 assigned for fax... (often no longer included...)

However, the N510 IP Pro DECT base does not have an RJ11 port. It is connected via LAN. Therefore, I thought I have to bring the telephone signal from the FritzBox into the network via the RJ11/RJ45 cable and then pick it up again on the ground floor. What would be the correct procedure to connect the DECT base on the ground floor?

2021-04-11 21:54:18

I can only speak about the GO 100. Base connected to Fritzbox via LAN. Whether switch or direct doesn't matter. Configure the base as an IP phone in the Fritzbox and then register mobile phones. It should be basically the same with the Pro.

2021-04-11 22:21:04

If you want to use a TAE connection of the Fritzbox, you can make a connection to a port of the patch panel and connect a telephone to the specific network socket port. However, this has nothing to do with the pure network.

Similar topics
17.01.2015	Multimedia and Wi-Fi and connections	22
05.01.2019	Doorbell/intercom system on Fritzbox 7490	16
30.08.2016	Commissioning of the network installation	76
11.05.2017	Improve Wi-Fi range/coverage	14
09.06.2017	Computer cables and Wi-Fi router	43
21.09.2017	Electrical planning - How many sockets are enough?	120
03.09.2024	Is a TAE socket no longer needed?	67
08.05.2020	Looking for a wireless intercom system with local power supply	34
08.01.2021	Are LAN sockets still up-to-date? WLAN/wireless is the future!	262
15.02.2020	Laying network cable	43
05.03.2020	Set up network with Unitymedia	28
04.11.2021	The secure, upscale network in the single-family house	59
13.09.2020	Do you have experience with the Cisco SG250X-24P-K9-EU switch?	57
07.03.2022	How to connect an outdoor camera? LAN, power or battery	25
01.09.2020	Which conduit for LAN cable?	32
08.09.2020	New Construction: Smart Home Combined with Alarm System Recommendation	19
29.08.2021	How do I get WiFi and phone service, technology in the basement	80
01.10.2020	(Smart) door intercom system planning on Fritzbox in new construction	16
01.09.2021	Network planning for a newly built semi-detached house - sensible or possibly overkill?!	15
13.05.2023	Planning electrical systems to be future-proof	257

FTTH/Network/DECT/IPTV is it correct?

knalltüte

Miwi2009

Tarnari

chamäleon

Tarnari

hanse987