IDM iPump 2-8 Optimization / Adjustment

2024-01-12 21:17:20

I still wouldn't rule out that something got mixed up. So it could still be that the pipes lead into another room and warm it up. Post a photo. As long as only the temperature between the rooms doesn't match, but it basically gets warm, I would first do nothing to the heat pump, but to the heating circuits.

I can do that tomorrow, I can't get to the distribution box right now because it's in the children's room and the little one is already asleep. Yes, basically it gets warm or warmer. But even in the living room it's only around 20°C when the thermostat is turned all the way up. That is actually still too "cold".

2024-01-12 21:20:21

It is important to understand that the thermostats usually simply just turn on or off. So at setting 6 it does not necessarily get warmer than at setting 4 if both settings lead to an open valve.

2024-01-12 21:27:47

It is important to understand that thermostats usually just switch on or off. So at setting 6 it does not necessarily get warmer than at setting 4 if at both settings the valve is open.

That is clear to me. That the valve is open at both settings is clear. But shouldn't the flow be different at thermostat setting 1 (or 4, doesn't matter) or 6?

2024-01-12 21:32:55

I understand that. That the valve is open in both settings is clear. But shouldn't the flow be different at thermostat setting 1 (or 4, doesn't matter) or 6?

Clear, or not clear, that is the question here. ;)

If no rare actuators are installed, there is only open and closed.
So either there is flow (temperature lower than setting), or there is no flow (temperature higher than setting).

For the hydraulic balancing, the adjusters under the thermal drives must be turned with a radiator key.
This then changes the flow.

2024-01-12 21:40:43

Clear, or not clear, that is the question here. ;)

If there are no rare actuators installed, there is only open and closed.
So either there is flow (temperature lower than setting), or there is no flow (temperature higher than setting).

For the thermal balancing, the adjusters under the thermal drives must be turned with a heating key.
This then changes the flow.

Ok thanks. Then I'll take a photo of it tomorrow, maybe that will help us move forward.
Thanks a lot anyway for the answers. :)

2024-01-13 15:20:05

Here are now the photos from the distribution box on the 1st floor.

On the left is child 2, the affected child's room that does not get properly warm. The second open valve is the bathroom; it does get warm here, but in my opinion, not up to the 23°C target temperature. However, I have not placed a thermometer here yet.

Similar topics
30.08.2025	Renovating children's room	11
08.03.2012	Children's room size/floor plan	12
21.10.2015	Air-to-water heat pump - Nest Thermostat	77
31.10.2015	Wall thickness children’s room / bathroom	35
05.11.2015	Blinds in the children's room and bathroom on the south side	12
22.02.2016	Size of the bedroom and children's room	38
02.06.2016	Children's room in the attic planned too small?	33
07.03.2020	Children's room on the upper floor open up to the roof	25
17.09.2016	Oops...! We actually need a children's room now...	19
15.10.2016	Renovation of children's room - split one window into two windows?	20
20.04.2017	Children's room with floor-to-ceiling windows	22
30.12.2019	Cork or bamboo for a children's room?	41
30.10.2019	Thermostat valves: meaningful?	17
13.11.2019	The children's room is too warm in the new building.	72
25.02.2022	Internet and telephone distribution box on our property	11
11.10.2021	Actuators are open but no flow	13
11.12.2021	Wall heaters do not reach the desired temperature	53
06.01.2023	Flow setting floor heating at the distribution box l/min	21

IDM iPump 2-8 Optimization / Adjustment

OBpunkt

RotorMotor

OBpunkt

RotorMotor

OBpunkt

OBpunkt