BSH VarioHinge & Miele XXL without cut-out baseboard

  • Erstellt am 2017-02-21 21:22:49

Nörgli

2017-02-21 21:22:49
  • #1
Hello everyone,

I have now spent hours reading about the dishwasher options. I will probably buy some XXL sink where I don’t have to improvise.
However, I definitely want to avoid having to cut out the toe kick.

Is that really the case with the Miele XXL & the BSH with VarioHinge (especially with Miele, since the front does not lift up)?
Unfortunately, I could not find any pictures or similar anywhere (especially of Miele – I don’t trust it because the recess doesn’t really help with the toe kick at first).

Dimensionally, I would adapt the kitchen to the toe kick (so toe kick 8cm + 80 cm cabinet = 88 cm bottom edge of countertop).

Regards,
Marco
 

IKEA-Freund

2017-02-21 22:45:43
  • #2
As for Miele: take a look at an assembly plan, for example.

miele.de/pmedia/ZGA/TX3324/10299750-000-01_10299750-01.pdf

Best regards,
IKEA-Freund
 

ikea_user

2017-02-22 08:04:42
  • #3
I already know that. Actually, that’s what unsettles me too. Or rather, I don’t quite understand.
In image 25, it is clearly cut out. In 27 & 28, this cutout is covered with a panel, but only if the baseboard is flush with the front (which it normally isn’t...)

And on top of that, I have read online & I believe also here in the forum that it works without the cutout (it ultimately depends directly on the ratio of front height above the floor vs. baseboard height).
Everywhere it is always only said that the installation of the XXL sinks from Miele & BSH Vario hinge is no problem. But no one says anything about the baseboard (or whether some are more skillful than others).
Actually, all baseboards should be the same in the regular Metod kitchen.
 

IKEA-Experte

2017-02-22 12:01:40
  • #4
Unfortunately, nothing or mostly nothing is reported about this and when you ask, there is no answer anymore. The minimum plinth height is only 35 mm at Miele and the plinth recess is larger at METOD than in other kitchens. If it is so important to you that the plinth panel is definitely not cut out, then why don’t you ask Miele if they have more data to be able to decide the question.
 

Similar topics
27.07.2017Miele washing machine with pre-ironing16
15.02.2017Fully integrated dishwasher19
23.10.2014Faktum AP with Ikea Metod kitchen15
09.04.2014Difference between Ikea Faktum & Ikea Metod kitchen16
12.09.2019Dishwasher fronts401
26.05.2015Ikea METOD / Dishwasher19
18.05.2015Ikea Metod/corner upper cabinet, why no 30/50 grid?11
24.10.2016Ikea Metod + BEHJÄLPLIG + Bosch Grundstück = Problem22
22.11.2016Installing Siemens dishwasher in Ikea Metod kitchen58
10.05.2015IKEA METOD search internal dimensions, side wall thickness?25
16.05.2015IKEA Rutinerad oven and Metod upper cabinet dimensions cable length sought14
09.07.2015Built-in refrigerator-freezer combo with fixed door at IKEA METOD10
31.10.2015Install Bosch SMV68M90EU dishwasher in Ikea Metod23
20.10.2015IKEA Metod Kitchen - Ideas / Suggestions for Planning?29
16.10.2017Bosch fridge-freezer combination for Ikea Metod cabinet 60x60x22016
12.07.2018Question about the Ikea Metod hanging rail21
30.08.2016Dishwasher not from Ikea11
02.09.2016Small kitchen with big possibilities wanted23
07.02.2017Quiet GSP with cutlery drawer wanted for Ikea Metod17
30.01.2017Ikea Metod cabinet for built-in Bosch refrigerator HND22K20011

Oben