Thermal balancing - Initial values taken for adjustment

  • Erstellt am 2020-12-03 15:04:45

Tx-25

2020-12-03 15:04:45
  • #1
Hello, I have now started working on the documentation to find out what the temperatures are like in our house. Attached is a link with a table. What do you think about the data? They have remained almost the same with relatively consistent weather. I am actually quite satisfied with the data. I have not made any changes after the hydraulic balancing yet.

It should be cooler in the bedroom on the upper floor. Can I simply reduce the flow rate there? Is there anything else that needs to be considered, since we have very short loops (from 16 meters :/)?

In the last four days, we have ventilated relatively little because we have a central ventilation system. As a result, there has naturally been no significant change in the values. Should I continue the documentation and ventilate more and differently over the next few days to test how the rooms heat up? The heating curve is currently set to 2 out of 10. Is an adjustment necessary here? [Linkbezeichnung]
 

seat88

2020-12-03 16:41:57
  • #2
Personally, I find it at least 3 degrees too cold. In the bathroom even 5...
 

RotorMotor

2020-12-03 17:40:29
  • #3
Yes, it would also be too cold for us. If you want it even colder in the bedroom, reduce the flow there.
 

Tolentino

2020-12-03 17:45:01
  • #4
Family Frost? I hope this is not just a quirk of yours or general thriftiness, but that your whole family is like that.
 

Mycraft

2020-12-03 18:11:50
  • #5
I can only say Brrrrr to that as well, but to each their own. And I would bet any bet that the values are not actually so smooth and fluctuate constantly. However, this is usually only visible through continuous monitoring. Random measurements rarely show the true picture. But just so much for the record.
 

Tx-25

2020-12-03 19:53:53
  • #6
Hm, we have never noticed anything negative regarding the temperatures. It was all identical in the previous apartment.

: I took the measurements at the same time of day, in the same place, with different thermometers (changing the thermometers). I can't get it any more precise.

Sure, I can increase the flow now. But I want to set the heating optimally. Does it make sense to change other parameters therefore?

: Don’t tell me you have more than 20 degrees in the bedroom too. Holy crap
 

Similar topics
05.02.2016What colors for the bedroom?44
15.02.2015Dressing Room/Bedroom Problem - Floor Plan Discussion25
20.02.2015Is the bedroom on the south side too warm?18
19.05.2015Heating children's room, bedroom, and bathroom14
09.09.2016Bedroom design35
07.02.2016Floor plan of master bathroom and passage to bedroom13
10.02.2016Looking for a clever bedroom idea with a walk-in closet19
22.02.2016Size of the bedroom and children's room38
26.04.2016Warm bedroom in the house with ventilation including heat recovery24
14.11.2016Carpet in the bedroom despite underfloor heating?36
13.10.2016Extra bathroom from the bedroom or storage room after all?29
20.04.2017Circuit - Bedroom - Ceiling Light / Bedside Lamp12
26.09.2017Skylight in the bedroom?13
09.01.2018Exhaust air in the bedroom - supply air in the storage room24
10.03.2018Children's room and bedroom - What size is recommended?56
09.02.2018Connection Bedroom / Dressing Room / Bathroom16
03.11.2018Moisture in the bedroom on the exterior wall - Where does it come from?10
14.11.2018Room thermostat with rotary knob from Busch Jäger30
09.12.2019Bathtub in the bedroom - what do you think about that?35
25.05.2022Bedroom too warm - despite the heating being off44

Oben