Screed is too low. Are there standards for this?

  • Erstellt am 2017-04-07 15:27:26

MatzeGalle

2017-04-07 15:27:26
  • #1
Hi,

I am currently arguing with my screed installer. I have installed vinyl throughout my entire house. Now I have noticed that the doorstep of the front door is much too high, as well as the terrace doors. Additionally, the interior doors should now be installed. Unfortunately, they do not fit. The cover strips do not cover the lintel. Now the screed installer says he assumed that tiles would be laid in the house and that is why he kept the screed so low. Are there any standards for something like this? Thanks
 

Nordlys

2017-04-07 15:30:13
  • #2
What did he have to assume? What is stated in the construction description? With tiles, he has to stay lower, just look at how thick they often are, compared to how thin PVC is. Karsten
 

MatzeGalle

2017-04-07 15:46:29
  • #3
Hello, there was no detailed construction description regarding the screed. I had taken the painter and flooring installation work from the offer of the [BU]. It also did not specify which flooring would be installed.
 

11ant

2017-04-07 15:50:04
  • #4
It is not uncommon that there are no detailed drawings for the floor construction for the craftsmen, such as (in mm from which material) it is built. Instead, there is only an indication like OK Finished Floor, or only an overall thickness can be derived from it. Then the craftsman just falls short to a sufficient degree based on his experience to make this possible. Especially if tiles were possibly indicated in the drawing and you instead use vinyl without him knowing, then his approach was exactly right. Imagine if it had gone the other way around, what a hassle it would be if the terrace doors would scrape over the tiles when swung open.
 

Nordlys

2017-04-07 15:52:54
  • #5
Aha. Communication problem. Everyone thinks their own part and does as they think, instead of saying what should be done. And now? I don't know anything either.
 

ypg

2017-04-07 16:05:30
  • #6
If nothing else is said or agreed upon, a thickness of 1 cm is assumed, which probably corresponds to a normal tile. If you have removed this position, you should have given the BU or screed layer a hint. -> screed without t ;) Regarding the door "edges" (top or bottom?) or the covering of the lintels, question marks arise for me... doesn't one contradict the other?

Be that as it may: door frame length should normally be adjusted individually on site.

Regards, Yvonne
 

Similar topics
28.04.2014What type of covering can be used in the bathroom instead of tiles?14
31.07.2016Screed does not extend into the reveals at windows / terrace doors on the ground floor12
06.08.2016Parquet or tiles with cats - are there concerns?11
05.11.2022Which flooring goes over tiles?19
23.08.2018Screed or tiles with a concrete look39
18.12.2018Underfloor heating, laminate, or tiles: which is warmer for the feet?35
08.01.2019Experience with gluing tiles on tiles?16
21.08.2019Tile choice - how/where to start?28
12.07.2019Offer for tile installation. Inspection12
10.11.2019Tiles or vinyl in kitchen and hallway19
19.11.2019Tiling the kitchen countertop24
30.09.2023Transition profile tiles -> vinyl flooring in "beautiful"11
19.11.2015Can I install click vinyl on floor tiles?10
19.08.2021Very thin screed, earth underneath - what to do?16
07.06.2023Remove tiled floor or lay parquet/vinyl on top?48
09.11.2021Black 2cm thick tar layer instead of screed??18
26.02.2022Concrete floor without screed on the upper floor/attic, what to do?24
26.09.2022Only screed in the garage - Driving in winter11
12.03.2023Cladding concrete stairs with tiles, vinyl, or parquet?24
17.07.2024Experience installing 60x60 tiles yourself?24

Oben